In this chapter we consider a more abstract approach to heat engine, refrigerator and heat pump cycles, in an attempt to determine if they are feasible, and to obtain the limiting maximum performance available for these cycles. The concept of mechanical and thermal reversibility is central to the analysis, leading to the ideal Carnot cycles. (Refer to Wikipedia: Sadi Carnot a French physicist, mathematician and engineer who gave the first successful account of heat engines, the Carnot cycle, and laid the foundations of the second law of thermodynamics). For more information on this subject, refer to a paper: A Meeting between Robert Stirling and Sadi Carnot in 1824 presented at the 2014 ISEC.
We represent a heat engine and a heat pump cycle in a minimalist abstract format as in the following diagrams. In both cases there are two temperature reservoirs TH and TL, with TH > TL.
In the case of a heat engine heat QH is extracted from the high temperature source TH, part of that heat is converted to work W done on the surroundings, and the rest is rejected to the low temperature sink TL. The opposite occurs for a heat pump, in which work W is done on the system in order to extract heat QL from the low temperature source TL and "pump" it to the high temperature sink TH. Notice that the thickness of the line represents the amount of heat or work energy transferred.
We now present two statements of the Second Law of Thermodynamics, the first regarding a heat engine, and the second regarding a heat pump. Neither of these statements can be proved, however have never been observed to be violated.
The Kelvin-Planck Statement: It is impossible to construct a device which operates on a cycle and produces no other effect than the transfer of heat from a single body in order to produce work.
We prefer a less formal description of this statement in terms of a boat extracting heat from the ocean in order to produce its required propulsion work:
The Clausius Statement: It is impossible to construct a device which operates on a cycle and produces no other effect than the transfer of heat from a cooler body to a hotter body.
Equivalence of the Clausius and Kelvin-Planck Statements
It is remarkable that the two above statements of the Second Law are in fact equivalent. In order to demonstrate their equivalence consider the following diagram. On the left we see a heat pump which violates the Clausius statement by pumping heat QL from the low temperature reservoir to the high temperature reservoir without any work input. On the right we see a heat engine rejecting heat QL to the low temperature reservoir.
If we now connect the two devices as shown below such that the heat rejected by the heat engine QL is simply pumped back to the high temperature reservoir then there will be no need for a low temperature reservoir, resulting in a heat engine which violates the Kelvin-Planck statement by extracting heat from a single heat source and converting it directly into work.
Notice that the statements on the Second Law are negative statements in that they only describe what is impossible to achieve. In order to determine the maximum performance available from a heat engine or a heat pump we need to introduce the concept of Reversibilty, including both mechanical and thermal reversibility. We will attempt to clarify these concepts in terms of the following example of a reversible piston cylinder device in thermal equilibrium with the surroundings at temperature T0, and undergoing a cyclic compression/expansion process.
For mechanical reversibility we assume that the process is frictionless, however we also require that the process is a quasi-equilibrium one. In the diagram we notice that during compression the gas particles closest to the piston will be at a higher pressure than those farther away, thus the piston will be doing more compression work than it would do if we had waited for equilibrium conditions to occur after each incremental step. Similarly, thermal reversibility requires that all heat transfer is isothermal. Thus if there is an incremental rise in temperature due to compression then we need to wait until thermal equilibrium is established. During expansion the incremental fall in temperature will result in heat being transferred from the surroundings to the system until equilibrium is established.
In summary, there are three conditions required for reversible operation:
All mechanical processes are frictionless.
At each incremental step in the process thermal and pressure equilibrium conditions are established.
All heat transfer processes are isothermal.
Carnot's theorem, also known as Carnot's rule, or the Carnot principle, can be stated as follows:
No heat engine operating between two heat reservoirs can be more efficient than a reversible heat engine operating between the same two reservoirs.
The simplest way to prove this theorem is to consider the scenario shown below, in which we have an irreversible engine as well as a reversible engine operating between the reservoirs TH and TL, however the irreversible heat engine has a higher efficiency than the reversible one. They both draw the same amount of heat QH from the high temperature reservoir, however the irreversible engine produces more work WI than that of the reversible engine WR.
Note that the reversible engine by its nature can operate in reverse, ie if we use some of the work output (WR) from the irreversible engine in order to drive the reversible engine then it will operate as a heat pump, transferring heat QH to the high temperature reservoir, as shown in the following diagram:
Notice that the high temperature reservoir becomes redundent, and we end up drawing a net amount of heat (QLR - QLI) from the low temperature reservoir in order to produce a net amount of work (WI - WR) - a Kelvin-Planck violator - thus proving Carnot's Theorem.
The first Corollary of Carnot's theorem can be stated as follows:
All reversible heat engines operating between the same two heat reservoirs must have the same efficiency.
Thus regardless of the type of heat engine, the working fluid, or any other factor if the heat engine is reversible, then it must have the same maximum efficiency. If this is not the case then we can drive the reversible engine with the lower efficiency as a heat pump and produce a Kelvin-Planck violater as above.
The second Corollary of Carnot's theorem can be stated as follows:
The efficiency of a reversible heat engine is a function only of the respective temperatures of the hot and cold reservoirs. It can be evaluated by replacing the ratio of heat transfers QL and QH by the ratio of temperatures TL and TH of the respective heat reservoirs.
Thus using this corollary we can evaluate the thermal efficiency of a reversible heat engine as follows:
Notice that we always go into "meditation mode" before replacing the ratio of heats with the ratio of absolute temperatures, which is only valid for reversible machines. The simplest conceptual example of a reversible heat engine is the Carnot cycle engine, as described in the following diagram:
Obviously a totally impractical engine which cannot be realized in practice, since for each of the four processes in the cycle the surrounding environment needs to be changed from isothermal to adiabatic. A more practical example is the ideal Stirling cycle engine as described in the following diagram:
This engine has a piston for compression and expansion work as well as a displacer in order to shuttle the working gas between the hot and cold spaces, and was described previously in Chapter 3b. Note that under the same conditions of temperatures and compression ratio the ideal Carnot engine has the same efficiency however a significantly lower net work output per cycle than the Ideal Stirling cycle engine, as can be easily seen in the following diagram:
When the reversible engine is operated in reverse it becomes a heat pump or a refrigerator. The coefficient of Performance of these machines is developed as follows:
________________________________________________________________________
Solved
Problem 5.1 - Reversible Home Air
Conditioner and Hot Water
Heater
________________________________________________________________________
Problem 5.2 - A heat pump is used to meet the heating requirements of a house and maintain it at 20°C. On a day when the outdoor air temperature drops to -10°C it is estimated that the house looses heat at the rate of 10 kW. Under these conditions the actual Coefficient of Performance (COPHP) of the heat pump is 2.5.
a) Draw a diagram representing the heat pump system showing the flow of energy and the temperatures, and determine:
b) the actual power consumed by the heat pump [4 kW]
c) the power that would be consumed by a reversible heat pump under these conditions [1.02 kW]
d) the power that would be consumed by an electric resistance heater under these conditions [10 kW]
e) Comparing the actual heat pump to the reversible heat pump determine if the performance of the actual heat pump is feasible,
Derive all equations used starting from the basic
definition of
COPHP.
________________________________________________________________________
Problem 5.3 - During an
experiment conducted in senior lab at 25°C, a student measured that
a Stirling cycle refrigerator that draws 250W of power has removed
1000kJ of heat from the refrigerated space maintained at -30°C. The
running time of the refrigerator during the experiment was 20min.
Draw a diagram representing the refrigerator system showing the flow
of energy and the temperatures, and determine if these measurements
are reasonable [COPR
= 3.33, COPR,rev
= 4.42, ratio COPR/COPR,rev
= 75% > 60% - not
feasible]. State the reasons for your
conclusions. Derive all
equations used starting from the basic definition of the Coefficient
of Performance of a refrigerator
(COPR).
________________________________________________________________________
On to Chapter 6:
Entropy - A New Property
______________________________________________________________________________________
Engineering Thermodynamics by Israel
Urieli is licensed under a Creative
Commons Attribution-Noncommercial-Share Alike 3.0 United States
License
